1

I'm trying to flash an Arduino Uno using usbasp but i'm getting the following error,I have checked all the connection and voltage using multimeter but still this error:

Arduino: 1.8.8 (Windows 10), Board: "Arduino/Genuino Uno"

C:\Users\SillyMonster\Desktop\arduino-1.8.8\hardware\tools\avr/bin/avrdude -CC:\Users\SillyMonster\Desktop\arduino-1.8.8\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -cusbasp -Pusb -e -Ulock:w:0x3F:m -Uefuse:w:0xFD:m -Uhfuse:w:0xDE:m -Ulfuse:w:0xFF:m 

avrdude: Version 6.3-20171130
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Users\SillyMonster\Desktop\arduino-1.8.8\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : usb
         Using Programmer              : usbasp
         AVR Part                      : ATmega328P
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : usbasp
         Description     : USBasp, http://www.fischl.de/usbasp/

avrdude: auto set sck period (because given equals null)
avrdude: warning: cannot set sck period. please check for usbasp firmware update.
avrdude: error: program enable: target doesn't answer. 1 
avrdude: initialization failed, rc=-1
         Double check connections and try again, or use -F to override
         this check.


avrdude done.  Thank you.

Error while burning bootloader.

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

I have tried different three other Usbasp but still same error

Different USPasp

Improve this question
12
  • This is the same dead programmer from before? Check the traces and connections on the programmer for shorts / open circuits. Also the cable. Commented May 12, 2019 at 9:58
  • @Majenko It's the dead programmer form before. I am using desktop with Intel Coffee Lake processor and MSI Z370 motherboard, can this cause any problem? Commented May 12, 2019 at 16:30
  • Take it out of the lake of coffee? Your computer is irrelevant. The fact that you have a known dead programmer is all that matters. Commented May 12, 2019 at 16:30
  • @Majenko Thanks Commented May 12, 2019 at 16:32
  • @Majenko i just need to flash the boot loader on an arduino uno, this time i'm using Arduino as ISP and getting this pastebin.com/3FhQfA6R, Connection: IMG1 IMG2 Commented May 12, 2019 at 16:56

1 Answer 1

Reset to default
2

The problem was with the Arduinos i have received from AliExpress All of them are using WAVGAT AVGA 328P-AU chips. I flasthed other Atmel MEGA 328P chip based Arduinos using USbasp and it's working fine. But i dont know how to flash those WAVGAT AVGA 328P-AU chips.

Improve this answer
1
  • I ran into the same issue. Those clone chips cannot be flashed over the ISP port. So you cannot change the bootloader at all. Just a piece of junk in my opinion. Commented Feb 11, 2020 at 9:14

Start asking to get answers

Find the answer to your question by asking.

Ask question

Explore related questions

See similar questions with these tags.