I have an original Arduino Uno board purchased directly from the official arduino website. I have used it successfully with IDE v1.8.5 on my Windows 10 laptop for various projects in the last 6 months.
Recently my laptop stopped working and I tried shifting the IDE to my old windows 8 laptop. I installed the latest IDE v1.8.8 on it. But whenever I am trying to upload the sample blink code to the arduino, I am getting the following - "stk500_recv(): programmer is not responding" error.
I have verified that the I have selected the right board - "Arduino/Genuino Uno" in the IDE. I can also see the driver installed in the windows "Device Manager" with COM3 as the port. I have selected COM3 as the port in the IDE as well.
Thinking that its a bit old windows 8 laptop, I tried installing the IDE on two other newer laptops (windows 7 and 10) along with the same troubleshooting steps as above. But unfortunately, same results.
I looked at the many links on internet and tried the following steps, but no luck so far.
- Resetting the board: It flashes the LED on the pin 13 twice which means the chips are ok and resetting the board. This where I think the board is functioning well.
- Tried using both "Upload" and "Upload using programmer" mode from IDE.
- Restarting laptops multiple times.
- Unplugging USB cable between laptop and arduino several times.
- Reinstalled arduino ide version 1.8.5 which was on my old laptop.
Do I need to choose Tools --> Programmers? I guess this is not needed as I am using USB to upload code, but please advice. What else can I try? Please help !!
Here is the complete error:
================================================================ avrdude: Version 6.3-20171130 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "C:\Users\Anurag\AppData\Local\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino14/etc/avrdude.conf"
Using Port : COM3
Using Programmer : arduino
Overriding Baud Rate : 115200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : Arduino
Description : Arduino
Hardware Version: 3
Firmware Version: 4.4
Vtarget : 0.3 V
Varef : 0.3 V
Oscillator : 28.800 kHz
SCK period : 3.3 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e950f (probably m328p) avrdude: reading input file "C:\Users\Anurag\AppData\Local\Temp\arduino_build_337690/Blink.ino.hex" avrdude: writing flash (930 bytes):
Writing | avrdude: stk500_recv(): programmer is not responding ######avrdude: stk500_recv(): programmer is not responding avrdude: stk500_recv(): programmer is not responding avrdude: stk500_recv(): programmer is not responding avrdude: stk500_recv(): programmer is not responding
Thanks in advance,
Anurag