kernel/git/firmware/linux-firmware.git/airoha, branch main

linux-firmware: update firmware for an8811hb 2.5G ethernet phy

2026-03-23T09:34:41Z

1. IEEE compliance optimization 2. Fix for incorrect parameter settings related to Pair swap 3. Surge 5R support 4. Temperature Sensor support 5. 2.5G/1G/100M link stability and performance optimization Signed-off-by: Albert Lee

linux-firmware: Add firmware for airoha-npu-7581 driver used for MT7990 offloading

2026-01-30T14:36:04Z

Add binary firmware for airoha-npu driver available on EN7581 SoC used to offload traffic to/from the MT7990 WiFi chipset. Signed-off-by: Lorenzo Bianconi

linux-firmware: Add firmware for airoha-npu-7583 driver

2026-01-15T21:04:05Z

Add binary firmware for airoha-npu driver available on AN7583 SoC. Signed-off-by: Lorenzo Bianconi

linux-firmware: add firmware for an8811hb 2.5G ethernet phy

2025-12-29T15:06:54Z

Add binary firmware for an8811hb 2.5G Ethernet PHY File: airoha/an8811hb/EthMD32_CRC.DM.bin File: airoha/an8811hb/EthMD32_CRC.DSP.bin Version: 25110702 Signed-off-by: Lucien.Jheng

linux-firmware: update firmware for en8811h 2.5G ethernet phy

2025-09-12T14:01:03Z

1.Fix the issue where the GPIO5 LED0 is reset when the network cable is not connected. 2.Optimize the auto-negotiation process to resolve the occasional negotiation failure issue. 3.Correct the internal packet processor settings to address the problem of some packets being lost due to header format. 4.Correct the internal packet processor settings to prevent packet blockage when interfacing with specific testing instruments. Signed-off-by: Albert-AL Lee Signed-off-by: Josh Boyer

linux-firmware: Add firmware for airoha-npu driver

2025-08-04T13:34:10Z

Add binary firmware for airoha-npu driver available on EN7581 SoC. Signed-off-by: Lorenzo Bianconi Signed-off-by: Josh Boyer

linux-firmware: update firmware for en8811h 2.5G ethernet phy

2025-02-18T12:48:27Z

1. Lower EMI emission without performance impact 2. Enhance inter-operability by adjusting auto-negotiation strategy 3. Fix a packet lost issue by adjusting internal packet processor configuration 4. Add a waiting mechanism to ensure the internal processor refrains from external access. Signed-off-by: Lucien.Jheng Signed-off-by: Josh Boyer

linux-firmware: update firmware for en8811h 2.5G ethernet phy

2024-10-14T14:03:34Z

1. Reinitialize the FNPLL clock during MD32 startup. 2. Optimize cable diag 3. Set Co-Clock default enable 4. Enable EMI Calibration Function 5. Enhance AN control mechanism 6. Fix internal bus arbitrator issue Signed-off-by: Lucien.Jheng Signed-off-by: Josh Boyer

linux-firmware: update firmware for en8811h 2.5G ethernet phy

2024-03-29T02:31:59Z

1. Fix the issue of external loopback 2. Fix the issue of down-shift 3. Add surge protection to support 0R and 5R mode 4. Enhance cable diag accuracy of cable length 5. Improved IoT performance and stability Signed-off-by: SkyLake.Huang Signed-off-by: Lucien.Jheng

linux-firmware: update firmware for en8811h 2.5G ethernet phy

2024-02-20T15:06:13Z

Release notes: - Improved IoT performance and stability. - Fixed the issue of 1G speed downshifting to 100M. - Added the loopback recovery function for 2.5G Ext, 2.5G Int, and 1G Ext loopback settings. - Fixed the issue of settings being lost when powering down and then powering up. - Fixed the issue of experiencing abnormal behavior when changing the speed to 100/1000Mbps and powering down/up. Signed-off-by: Lucien Jheng Signed-off-by: Shayne Chen Signed-off-by: Josh Boyer