Newest Questions
25,033 questions
0
votes
1
answer
75
views
How to adapt this ESP32 + TMC2240 stepper controller design to my project?
I’m trying to build a wireless stepper motor controller using an ESP32 with a TMC2240 driver. I came across this reference design: Wireless Stepper Motor Controller with ESP32 and TMC2240 https://www....
- 61
0
votes
1
answer
95
views
Why does my stepper motor have jerky motion with DRV8825 microstepping?
I’m using a NEMA 17 stepper motor (model 42SHDC3030Z-23WB-1 / 17HS4401S) with a DRV8825 driver with small radiator and an ESP32. Even when set to 1/16 microstepping, the motor motion is very jerky.
It ...
- 11
1
vote
1
answer
70
views
HC-12 receives garbage, but the garbage is consistent
I'm playing with two HC-12 wireless communication modules. After setting AT+FU4, I tested the modules, but the communication appeared to be unreliable in one direction. I tried to simplify the code as ...
- 246
0
votes
1
answer
79
views
Information about PWM frequency
Previously, the reference page for the analogWrite function showed the PWM frequencies for different pins on different Arduino boards, but now it doesn't mention it anywhere... Where is this ...
- 111
0
votes
1
answer
50
views
Send uint32_t over i2c from attiny85 slave to atmega328p master
I run into an issue with querying a uint32_t with an atmega328p master from an attiny85 master.
I have put both codes below.
I did run the equivalent code for just sending a uint8_t and all works ...
- 163
-1
votes
1
answer
120
views
Connecting the device to Arduino via the UART protocol
The essence of the task
I have a task to connect an external device with my arduino and transfer data to each other via the UART protocol. The external device has 4 pins (Two for power supply and RS-...
- 1
0
votes
2
answers
117
views
problem with scripts in Arduino Lab for MicroPython
I am trying to set up an Arduino Nano ESP32 so that I can code in MicroPython. I successfully installed Arduino Lab for MicroPython and flashed the firmware onto the device, but when I try to run the ...
- 1
0
votes
0
answers
87
views
Cannot get Arduino Nano with CH340 chip to keep working
I have a bunch of Arduino Nano boards with the CH340 chip. When I want to upload code to a board, it sometimes works the first time, sometimes it doesn't. Afterwards, it mostly doesn't work anymore.
...
- 129
0
votes
0
answers
74
views
ASync Timer2 based OSCCAL value
How to calibrate the internal RC oscillator off of a 32768 Hz crystal serving Timer2?
void OSCCAL_calibrate(void) //This version specific to ATmegaXX8 (tested with ATmega328)
{
unsigned char ...
- 136
0
votes
0
answers
45
views
Cannot ping a host unless I use parseIP from Ethercard
I'm trying to write an Arduino sketch which pings multiple hosts and switches some RGB LEDs to indicate the status of the devices on my network. This question is a followup of ParseIP in the EtherCard ...
- 129
0
votes
0
answers
43
views
After an USB disconnect the program I've uploaded to the Arduino Mega 2560 doesn't work properly anymore, why?
For a race simulator I'm using several Arduino Mega 2560 boards on which the code that will post below will be running. (not my code! But freely available on the internet)
Everything works fine, just ...
1
vote
0
answers
53
views
Why LoRa Ai Thinker 433Mhz doesn't go in Receive mode after we send ACK? [closed]
So basically I created a simple Receiver and Transmitter using Two Lora Ai Thinker 433Mhz (Sx1278). I am using Esp8266 with one Lora (as transmitter). It sends packet when we press button. On Receiver ...
- 11
0
votes
1
answer
98
views
Arduino DUE - I Have enabled A14, will this break anything?
I developed a quick custom PCB using the ATSAM3X8EA-AU as I wanted to use Arduino to program it as an Arduino DUE, I kept most of the schematic the same, however I used pin A14 pin 52 as an analog ...
- 117
0
votes
1
answer
82
views
How to timeout hung incoming connections to the Ethernet port?
If I telnet to an Ethernet capable Arduino (e.g. shield, Leonardo, Leonardo Eth) with something like telnet [ip] [port] and then do nothing, the connection hangs. Seemingly for ever, or at least ...
- 129
0
votes
0
answers
35
views
Reassigning GPIOs 6-11 on a 30 pin ESP Wroom 32
I am trying to wire up the ESP 32 based Crunch-E keychain synth (gituhub repo with wiring diagram here).
In my case I am using a 30 pin ESP Wroom 32 board with pinout diagram here.
The Crunch-E wiring ...
- 101