Questions tagged [mkr1010]
The mkr1010 tag has no summary.
27 questions
0
votes
1
answer
75
views
MKR1010 Interference when relay motor engages?
I am a complete beginner. Are Arduino products really flaky?
I've thrown together the circuit in the diagram - an MKR1010 in a relay shield. I've wired up 2 sets of sensors, an LCD screen and a motor. ...
- 9
0
votes
2
answers
483
views
What kind of power cable do I need for the MKR 1010?
I see very confusing documentation on powering the Arduino MKR 1010. I would like to know what kind of cable to power it with (a weird connector port on its side).
Can I just put 5 V + (AC or DC?) on ...
- 35
0
votes
1
answer
257
views
MKR 1010 voltage confusion
I'm very confused about powering my MKR 1010 on a breadboard. It says use USB, but that is 5.5 V and it specifically says never go above 3.3 V, yet there is a 5 V pin. So what size external power ...
- 35
0
votes
1
answer
822
views
Connecting the MKR GPS shield by cable or as a shield
I have an MKR WiFi 1010 and an MKR GPS Shield. When I connect my GPS Shield using the I2C cable, it works fine.
This works perfectly (the bottom is the MKR Motor Carrier):
However, when I use it as a ...
- 195
3
votes
1
answer
489
views
Wireless programming of Arduino
I'm trying to find a convenient way to program my Arduino remotely (by Bluetooth or Wi-Fi) because it will be packed and placed outside of my working place. Found a few ways (Arduino Cloud and Blynk) ...
- 133
0
votes
1
answer
2k
views
What is the correct way to externally power a MKR 1010 WiFi
I'm a little confused by the powering arrangements of the MKR 1010 WiFi. I need to power it on a breadboard from an external power supply. I will not be using a LiPo battery and I need it to work when ...
- 305
1
vote
1
answer
546
views
MKR 1010 disconnects COM-port on each upload
Each time I attempt to upload to the MKR WiFi 1010 board the COM-port gets disconnected, usually at one of the following points:
Either it disconnects just after compiling/verifying. In this case the ...
- 141
2
votes
0
answers
341
views
Why does the MKR WiFi 1010 LED_BUILTIN sometimes pulsate?
Sometimes the built-in LED pulsates after an upload. It could be after a failed upload but I'm not entirely sure. What does this indicate? I haven't been able to find any information about it.
It ...
- 141
0
votes
1
answer
293
views
I can't turn on the motor by Arduino IoT Cloud
I'm trying to turn ON/OFF a DC motor from Arduino Iot Cloud. I have to turn it ON/OFF physically and through the cloud, physically it works well but from the cloud it does nothing. I'm using an ...
1
vote
0
answers
525
views
Fried 2 MKR Wifi 1010 after plugging them to a solar panel
I fried 2 MKR Wifi 1010 after powering them using a solar panel.
Here is the diagram:
Both were working fine as long as I used the LiPo battery and/or my macbook (using USB) as power sources. They ...
- 119
1
vote
1
answer
717
views
How do I connect an MPU6050 sensor to an Arduino MKR WIFI 1010?
I've been trying to connect an MPU6050 to my MKR WIFI 1010 following these general instructions and using the I2CDev library, but I keep running into problems.
For a while the Arduino just didn't show ...
- 33
-1
votes
1
answer
308
views
Computer doesn´t recognize MKR1010
I´m learning how to use the Arduino MKR1010. When I wrote a program for controlling LEDs and to read a BMP280 sensor with a web aplication, and I uploaded the program to the board, suddenly the ...
- 99
1
vote
2
answers
2k
views
Sending arduino sensor data via WiFi to a MySQL server
I'm aware this question has probably been asked many times but I'm pulling my hair out.
I'm trying to get sensor data from an arduino to a MySQL server. I've checked the apache access log and the ...
- 31
0
votes
2
answers
1k
views
Wire.endTransmission() hangs, but only, if wire.begin(); is called with an address (MKR WiFi 1010)
This code runs without issues, scoped and seen from serial output:
#include <Wire.h>
void setup() {
// put your setup code here, to run once:
Serial.begin(115200);
Wire.begin();
Wire....
- 101
2
votes
1
answer
748
views
Does the MKR WIFI 1010 support the arduino mouse and keyboard controller?
I am working on a project right now that needs to connect to my computer via bluetooth and access the arduino mouse and keyboard library. In my research, I've found that only the Leonardo, Due, and ...
- 21