Skip to main content
Arduino

Questions tagged [gps]

Ask Question

Global Positioning System. Uses satellites to determine geographic location.

248 questions
Newest Active Bountied Unanswered
1 vote
1 answer
163 views

I have a GY-GPS6MV2 connected to a nano. (Also tried UNO same result). RX on GPS goes to TX of Nano PIN 3 and TX on GPS to PIN 4 on Nano. When I run the code below all I get is a set of numbers. They ...
TomTheTec's user avatar
  • 13
0 votes
2 answers
946 views

I've bought a Heltec Wireless Tracker Arduino. I want to get the GPS position. I've taken the original example "GPSDisplayOnTFT" from the IDE (I've made a few changes because the original ...
Jaime Roman's user avatar
  • 139
1 vote
2 answers
499 views

I am making a gps tracker with neo6m gps module and esp32 dev board. I checked wiring and coding but still my module isn't catching a signal I am already on roof of my house in case it require clear ...
Yug Ahuja's user avatar
  • 33
-1 votes
1 answer
169 views

I've disassembled a drone and found a GPS module. I want to use it. I haven't found any information about the architecture and the Serial.begin value I have to use. Could I break it if I tried ...
drMAIN's user avatar
  • 1
-1 votes
2 answers
173 views

I have a project (still planning) with three I2C sensors: GPS, 3-axis gyro+accelerometer, and OLED. Do I connect SDA/SCL in series, or do I connect them in parallel?
Marifin -'s user avatar
  • 29
1 vote
0 answers
153 views

I have been using a MKR WiFi 1010 board with GPS shield for a very long time (year+) and have not been able to solve my problems with the GPS data dropping out. The setup for my field application is a ...
ktn8rgrl's user avatar
  • 11
2 votes
1 answer
2k views

I've designed a test PCB that utilizes an ESP32 S3 and testing pins. During program uploads, I use the USB interface over GPIO20 and GPIO19 as D+ and D-. Everything works fine in this configuration. ...
mehmet's user avatar
  • 297
2 votes
0 answers
649 views

I have built a speedometer, based on this youtube video: https://www.youtube.com/watch?v=gKuJxjxNP-k&t=34s The speedometer is for a car, so it needs to be in real-time and accurate, with the ...
cool bean's user avatar
  • 31
0 votes
1 answer
278 views

I want to build a speedometer for a car using Arduino UNO. For the display, I'm using an LCD screen that will be located behind the steering wheel. For context, I'm building the speedometer for a ...
cool bean's user avatar
  • 31
1 vote
0 answers
256 views

I have an Arduino UNO with SIM808 and I'm trying to send my GPS data to the Firebase. I have successfully get a location from SIM808 via serial. However I found that Arduino only supported HTTP ...
Harits LH's user avatar
  • 11
1 vote
0 answers
86 views

i trying to interface ATSAMD21G18A-U to NEO-M8N-0-10 gps by using UART. my problem is here, i need to use pin 25(rx) and 26(tx) of arduino to interface. i have tried below. but getting error:C:\Users\...
Anantha Venu's user avatar
  • 11
1 vote
0 answers
92 views

I designed PCb for relay Switching using gps signal for that i am using atmaga 328P-AU and Neo 6M but after connecting gps module its not showing long, lat. i also checked power supply in module pin ...
Jay Vadoliya's user avatar
  • 21
1 vote
0 answers
88 views

Below is my current code for connecting to the A9G. As far as I can tell, it never actually opens a connection as HWSERIAL.println("AT"); does not return anything. Any ideas would be ...
Tom Callan's user avatar
  • 11
-1 votes
1 answer
1k views

I bout a NEO-M8N gps module but I can't connect to u-blox softwares (both u-center2 & u-center_v22.07) It seems to be one of the junk modules that China mass-produces Module's pictures : I tried ...
Curious guy's user avatar
  • 113
-1 votes
1 answer
294 views

I'm using Nano Every and SIM33EAU GPS module for my project and today I went riding shotgun to test how it works when moving on the road. I am using u8g2 library and one of the things that I have ...
Varonne's user avatar
  • 89

15 30 50 per page
1
2 3 4 5
…
17