Skip to main content

Questions tagged [nimh]

A nickel–metal hydride battery (NiMH) battery is a type of rechargeable battery. They have a better energy density than nickel–cadmium batteries (NiCd or NiCad) and have largely replaced them in many applications.

0 votes
1 answer
118 views

End of discharge voltage for "refreshing" of NiMH cells

I have been reading some books on NiMH batteries. Some authors state that for optimum performance and longevity NiMH batteries need to be "exercised" or "refreshed" or "...
Thomas Anderson's user avatar
1 vote
1 answer
68 views

Charging NiMH: What happens if your varying charge voltage goes too high or too low?

I'm researching NiMH batteries, and I understand that these batteries charge via CC, but what I don't understand is what happens if you have a CC source, but the voltage goes above the max battery ...
J. Street's user avatar
  • 331
0 votes
0 answers
40 views

Is it a bad idea to apply 12V to a NiMH 4S1P battery to revive it?

I have a stock of batteries with 4 NiMH cells in series. The issue is that many of them are at 2.4V, which is a very low voltage (0.6V per cell). I’ve seen articles suggesting that applying ...
H2fumes's user avatar
0 votes
2 answers
178 views

Charging Ni-MH batteries

I understand that the recommended charging voltage for AA/AAA NI-MH batteries is between 1.4 V to 1.6 V and c/10 charging current. If i need to choose between 2 options: Charging voltage of 1.4 V and ...
Dan's user avatar
  • 87
0 votes
0 answers
131 views

Charging circuit for Raspberry Pi Pico

Currently I am working on a kind of pager project. The main idea is that a base station communicates via LORA with my handheld, similar to a DECT phone (Fritz!fon, Gigaset, ...) The handheld should ...
dev_clavis's user avatar
1 vote
1 answer
63 views

Identification of NiMH connector

What kind of connector is this? It's from a NiMH battery.
Sidewinder's user avatar
0 votes
0 answers
56 views

TP4056 charge discharge for a NiMH prius battery?

I want to make a capacity tester for a 6 cell module for prius batteries. They have 6000mAh new and anywhere from 2500-5000 mAH used. I was wondering if theTP4056 would work for a NiMH battery and if ...
crispYpickle's user avatar
1 vote
1 answer
132 views

What ways can I test an NiMH battery aside from capacity

In my current job, I take used prius batteries and recondition them. I put them on RC chargers and the modules through charge/discharge cycles to both measure and raise the capacity. They have an ...
crispYpickle's user avatar
0 votes
2 answers
55 views

D-cell Ni-Mh 12v battery-pack (10S) ok for a 12v device that can be a little heavier/bulkier?

In a previous question I was asking about a way to use dc charging in combo with an 18650 battery pack for an audiobox. Since site rules mean I cannot change or add to that question after it has been ...
Respoda555's user avatar
0 votes
0 answers
39 views

Modifying Li-po and NiMH batteries

I have three 2s 7.4V LiPo batteries, two balance LiPo chargers that can charge 7.4V/11.1V 1s-3s batteries, and soldering tools lying around, so I'm wondering: Can I convert the three 2s 7.4V batteries ...
Beachy Boys's user avatar
1 vote
2 answers
333 views

How might one attempt to recover a fully drained NiMH cell? [closed]

While the particular devices in this question are "consumer" NiMH cells; I am looking for a general answer, based on electrical engineering principles, that applies also to "non-...
cjs's user avatar
  • 1,058
0 votes
0 answers
30 views

NiMH Battery Pack, lowest cell in pack dies

I've built several NiMH packs and for some reason, the lowest cell in each pack dies in storage. I recharge them once per month when in storage, and do a forming charge once every 3 months, but I keep ...
Jedi Engineer's user avatar
2 votes
1 answer
282 views

Battery pack voltage keeps dropping without use

I have a battery pack for a circa 2008 Black & Decker 9.6 V electrical screwdriver. It was not holding a charge so I replaced its batteries. It had eight NiCd 1200 mAh batteries. I replaced them ...
Sabuncu's user avatar
  • 405
1 vote
1 answer
123 views

Selecting a charge time for a NiMH charger at 1C

I'm building a solar charger for an Energizer 8.4 V, 175 mAh NiMH battery with a MAX713. The solar panel is 15.4 V, 200 mA. If I charge them at 1C (175 mA), would it be better to set the charge time ...
488 Studios's user avatar
0 votes
2 answers
115 views

NiMH battery charging problem

I have a battery (8 cells in series, NiMH AA cells (1.2 V to 1.3 V), 1300 mAh per cell). Cells used- https://www.amazon.in/Rechargeable-NiMH-2300-Peak-Power/dp/B01MF8HUKO https://www.amazon.in/...
funtastic rdj's user avatar

15 30 50 per page
1
2 3 4 5
14