0

(I'm sorry for my bad English, but I will do my best)

I have a Chinese MUC which already programmed. It communicates with a LED driver chip using three wires (STB,CLK,DIN).
(LED driver controls 16 digit 7 Segment display)

After some research, I found that it can be talk to LED driver using shiftout function.

Now the main coal is to connect these 3 pins(STB,clk,din) to Arduino and read the incoming data and convert the data to numbers.

To test if this idea is working or not, I came with two arduino (uno to send shiftout function and mega to read it) after connect pin 2 of uno to pin 2 of mega and same 3 to 3, 4 to 4 and also Gnd of uno to Gnd of mega.
I wrote these codes:

arduino UNO side (to send shiftOut function)


    #define STB  4
#define clockPin  5
#define dataPin  6

void setup() {
  Serial.begin(9600);

  pinMode(STB, OUTPUT);
  pinMode(clockPin,  OUTPUT);
  pinMode(dataPin, OUTPUT);
}

void loop() {
 digitalWrite(STB, LOW);
    shiftOut(dataPin, clockPin, LSBFIRST, 0b10101010 ); // 1st digit   
   digitalWrite(STB, HIGH);
}

arduino mega side (to read shiftOut function)


    #define STB 4
#define clockPin  5
#define dataPin  6

 int R_STB[8]; 
 int R_clockPin ;
 int R_dataPin ; 
void setup() {
   Serial.begin(115200);

  pinMode(STB, INPUT);
  pinMode(clockPin,  INPUT);
  pinMode(dataPin, INPUT);
}

void loop() {

 R_STB = digitalRead(STB); 
 R_clockPin = digitalRead(clockPin);
 R_dataPin = digitalRead(dataPin);


   for(int i=0 ; i<8;i++){
  Serial.print(R_STB[i]-2);

  Serial.print(" ");
  Serial.print (R_clockPin[i]);

 Serial.print(" ");
  Serial.print(R_dataPin[i]+2);
Serial.println(" ");
   }
 }

But the digital read at arduino mega side can't read all data due to it fast switching between High LOW statement maybe? and I am stuck here.

Please any one has any ideas?

Improve this question
1
  • 1
    Welcome to Arduino StackExchange. What the Chinenese MUC you have, provide us some the datasheets Commented Aug 3, 2019 at 14:31

1 Answer 1

Reset to default
1

You are right that you can't read the data fast enough with your method there. What you really need is the opposite of "shiftOut" - which happens to be called "shiftIn". You use it just like shiftOut, but instead of you sending it a value to send it instead returns a value that it reads.

You trigger it using the "STB" pin:

if (digitalRead(STB) == LOW) {
    uint8_t val = shiftIn(dataPin, clockPin, LSBFIRST);
    Serial.println(val, HEX);
}

But the protocol you describe is simply SPI. There is hardware within the Arduino to handle it for you. A little harder to work with, but it's capable of working at much higher speeds and is more likely to be able to read your incoming data fast enough.

Resources:

The latter includes how to configure an SPI "Slave" which is used for receiving data that is sent out from elsewhere.

Improve this answer
6
  • Majenko thank you vary much . I read about the SPI and i reach to the solution, one question please what if i got just two pin (DIN,CLK) instead of three(STB,CLK,DIN) how or what should i use? thank you in advance. Commented Aug 5, 2019 at 12:37
  • For SPI there must be a third pin. It may be labelled CS or SS instead of STB. Or it may not be SPI and have a "Latch" pin (it's a shift register in that case). If there's nothing but CLK and DIN then there must be some other non-standard method for indicating the start of a communication block. Commented Aug 5, 2019 at 12:39
  • Thank you for your fast reply, The new LED driver (TM1640), it says in it datasheet "Dual-line serial interface (CLK, DIN) " . datasheet==>> datasheetspdf.com/pdf-file/838954/TitanMicro/TM1640/1 Commented Aug 5, 2019 at 12:44
  • It uses a non-standard system: The starting condition of data input is: when CLK is high, the DIN becomes low from high; the ending condition is: when CLK is high, the DIN becomes high from low. Commented Aug 5, 2019 at 12:54
  • could you suggest any think which by reading it I can handle the data which comes from (MUC) through(CLK, DIN) pins using arduino?please Commented Aug 5, 2019 at 14:16

Start asking to get answers

Find the answer to your question by asking.

Ask question

Explore related questions

See similar questions with these tags.