Questions tagged [temperature-sensor]
A component which measures heat.
227 questions
0
votes
1
answer
75
views
Change I2C address of Arduino Modulino Thermo
I want to use several Arduino Modulino Thermo modules in one project and therefore change the default I2C addresses of the sensors. On the internet, I find conflicting info about if this is possible.
...
- 1
0
votes
1
answer
538
views
Set SPI Mode on Arduino Uno R4
I am switching a code from Arduino Uno R3 to Arduino Uno R4 Wifi due to the limitation of RAM spaces on R3. I use a thermocouple shield and SD Card read/write shield with the project, which requires ...
- 3
1
vote
2
answers
297
views
Why is my BME280 sensor returning 0 for all data values?
My BME280 is returning 0 for temperature in Celsius, 0% humidity, 0.00 pressure (hPa) and 44330.00m for altitude. I am connecting it with I2C on a Raspberry Pi Pico and everyone on the team has ...
1
vote
0
answers
99
views
Help with combining sensor codes
I'm trying to combine 4 sensors' codes into one to display on the serial monitor: MAX30205, MAX30100, AHT20, and ENS160. I'm using the Adafruit ESP32 Feather V2 board. Here are the libraries that I've ...
1
vote
2
answers
386
views
DHT20 and OLED display not working together
I am trying to get my DHT20 and OLED (both from the Arduino Sensor Kit) to work at the same time. I am able to get them working separately with their respective test codes, but when I try to combine ...
2
votes
2
answers
987
views
Arduino read thermocouple Type K with ADS1115
I ordered a ADS1115 so I could measure temperature of a type K thermocouple, but I am not managing to get accurate readings. I had it working while having a normal A0 pin, but since the type K table ...
- 123
0
votes
0
answers
999
views
ESP32 S3 Same code works on Serial1 but NOT on Serial0 for RS485 module
I have designed a test board to understand ESP32-S3 working pins. I am using USB interface D+, D- for programing so Serial0 is free to use.
This is my test circuit for testing an RS485 converter. For ...
- 297
3
votes
1
answer
436
views
Arduino Servo with temperature sensor (TMP36)
The essence of the program is to measure the temperature, and if the temperature is higher than 26 degrees, the servo rotates by 45 degrees, and if it's lower, it rotates by 179 degrees. However, a ...
- 133
0
votes
1
answer
196
views
DS18B20 doesn't work reliably
like discribed in the title my temperature sensor goes to -127 after a few minutes of run time, it works again after a restart, I have already replaced the sensor and I'm using the same code for the ...
- 21
2
votes
0
answers
113
views
Slow I2C communication
To collect temperature and BPM, I connected a max30101 in my Heltec WiFi kit V3 with ESP32. The data collected are stored in arrays to extract statistical features from signals which an algorithm will ...
- 31
-1
votes
1
answer
450
views
NodeMcu V3 & BMe280 -> Temperature, Humidity, Pressure: value nan
I've just started playing around with a NodeMcu V3 and a BME280 sensor.
wiring
VCC -> 3.3V
GND -> GND
SCL -> D1 (GPIO5)
SDA -> D2 (GPIO4)
I've tried this sketch / I2C scanner: it finds ...
2
votes
2
answers
772
views
DS18B20 oneWire analog vs digital
I just discovered that the Dallas DS18B20 can be read from either digital or analog pins. I never thought analog was an option until I stumbled across an article searching for another issue.
So now I'...
1
vote
0
answers
113
views
Which temperature sensor is accurate?
I have an Arduino Nano RP2040 Connect with two temperature sensors. A DHT22 is connected to D2 and pulled up with a 5 kΩ resistor to 5V, and a LSM6DSOX IMU is built in to the board. Here's my code:
#...
0
votes
1
answer
227
views
Temperature is not updated on OLED screen - Grove components
I am using 2 grove components in order to display a temperature. I use an I2C High Accuracy Temperature Sensor - MCP9808 and an OLED Screen using this script:
#include <U8g2lib.h>
#include <...
- 131
1
vote
1
answer
406
views
DHT11 temperature and humidity sensor Code
I’ve got a question about this code I’ve attached please- would it be correct to read it like this:
After defining the variable temperature and humidity and assigning measurement_timestamp to millis(),...
- 13