Questions tagged [practical]
The practical tag has no summary.
38 questions
2
votes
5
answers
268
views
How do I modify automotive jumper cables to safely jump an 8 volt system with a 12 volt car battery?
I have an antique truck using an 8 volt battery conversion from its original 6 volt because the starter turned too slowly to crank it. This protected the instruments from damage. If I need to jump ...
4
votes
3
answers
1k
views
How do I learn to build practical stuff? [closed]
I am in my 4th semester of a 4-year undergraduate electronics rngineering program. All I have learned so far is lots of theory in courses such as analog electronics circuits, digital electronics ...
- 515
1
vote
1
answer
126
views
AC RMS from half wave controlled rectifier
I have built the following circuit:
I measured the AC RMS at output as 975.8 mV:
I can't get anywhere close to that measured value when using the AC voltmeter formula below (for delay angle of 90):
...
- 33
1
vote
1
answer
478
views
How do I calculate the transfer function of this basic terminated RC filter?
I'm reading through an electronics book to teach myself, and I'm in the section about filters. I've been following along so far, but now I'm confused about how the author came to a conclusion in his ...
- 13
-7
votes
1
answer
281
views
Why do people learn electronics? Need some practical examples [closed]
Examples of why one would to learn electronics are:
1) He works (or intend to) as an electrical engineer
2) He likes (or needs to) repair electronic equipment
One thing I find it difficult to ...
- 89
0
votes
2
answers
158
views
The mean value of phase noise as a stochastic process
What is the mean value of phase noise as a stochastic process?
Where can I get a theoretical analysis of this topic?
- 61
0
votes
1
answer
525
views
Bypass LED with switch (why)?
I have a schematic attached that appears to show a switch bypassing an LED, or the other way around. In the working device operating the switch lights the LED and engages (as in turns 'on' a 'normally'...
- 103
0
votes
2
answers
2k
views
How to experimentally measure damping in RLC circuits?
I know there are methods to theoretically determine the damping factor and quality factor in RLC circuits. Equations such as
$$\zeta = \frac{R_s}{2} \sqrt{\frac{C}{L}}$$
$$Q = \frac{1}{2\zeta}$$
...
0
votes
1
answer
72
views
What would be involved in rectifying electricity from a faulty car alternator?
Disclaimer: Newbe
As I understand things:
a car "alternator" generates a/c current
the alternator contains diodes that rectify the current to d/c current
if one or more diodes fail then the ...
- 105
1
vote
0
answers
157
views
Question regarding dielectric breakdown (especially for stun guns)
This question occurred to me after looking at some models of stun guns. What I noticed was that some of them like one I bought had metal extensions sort of like prongs, or like tiny metal cones. I ...
- 537
1
vote
2
answers
819
views
How to measure resistance with a multimeter?
This may be a very simple question. In my lab guide (I am a freshman Electronic Engineering student), we are supposed to build and analyze a circuit on a breadboard. First, we need to select some ...
- 617
2
votes
1
answer
1k
views
The effects of Op amp Bias current
This is regarding an integrator op amp design, the rate at which the input voltage charges the integrator's feedback capacitor is 150V/s. I am trying to justify the minimum feedback capacitor value ...
- 131
0
votes
2
answers
1k
views
Can reverse voltage gain for a BJT be negative?
While observing the input characteristics of a Bipolar Junction Transistor(BC547), I observed from the graph that the reverse voltage gain came out to be negative. Is this possible and if so, what is ...
- 381
0
votes
2
answers
2k
views
What is the simplest possible monostable 555 timer circuit?
Say for instance, the goal is to light an incandescent bulb for x amount of seconds (let's say 20).
What is the simplest configuration possible?
Of course, simple timer circuits aren't rare, and can ...
- 1,109
0
votes
2
answers
694
views
MOSFET Biasing Problems
I am interested in finding Vgs for E-MOSFET for desired Id or/and Vds. Referring to those equations of drain current in saturation region, value of conduction parameter "K" would be nice to have but ...
- 2,524